Elite CSW200UL Manual de usuario

CSW-200CSW-200High Traffic Commercial Swing Gate Operator

ADJUSTMENT OF OUTPUT SHAFT2. Place the red handle in 90° position.By tightening the nut you will be able to adjust the clutch.A. Release the red handl

CHOOSING MOVEMENT DIRECTIONHOW TO CONNECT POWER (120V)OPEN TO THE RIGHTOPEN TO THE LEFT

CLUTCH ADJUSTMENTI M P O R TA N T !The adjustment is for a gate thatis over 300 pounds and 12 feetlong or longer. While the gate is closing, instantly

T W O - WAY ADJUSTABLE REVERSING SENSORA D J U S TA B L E T I M E RTimer can be set from 1 to 60 seconds (Timer ON), or for push open/push close

MASTER AND SLAVE WITH TIMER ONUse shieldedtwisted wireConnect G from master to G of slave. (G is the shield or a ground wire)Connect B from master to

MASTER AND SLAVE WITH TIMER OFFPA RTIAL MASTER/INDIVIDUAL CONTROLIN ORDER FOR THE FOLLOWING OPERATION TO OCCUR, FOLLOW THE INSTRUCTIONS.EXAMPLE: There

INSTRUCTIONS FOR OPTIONAL SYSTEMSMaglockorSolenoid10 & 11 - Burglar Alarm Output12 & 13 - Burglar Alarm Input14 - Ground15

SOLENOID CONNECTION WITH OPTIONAL BOARDMAGLOCK CONNECTION WITH OPTIONAL BOARDOptional Omni board neededModel # O-OMNI EXBOptional Omni board neededMod

SOLENOID/MAGLOCK J3 CONNECTIONWire Harness

HOUSE ALARM/PROXIMITY SWITCH CONNECTIONS

UL LISTINGS AND INSTRUCTIONSINSTALLATION INSTRUCTIONS REGARDING THE GATE OPERATORA) Install the gate operator only when:1) The operator is appropriate

OPTIONAL BUILT-IN LOOP DETECTORSTHREE PUSH BUTTON STAT I O NC A U T I O N :Use diff e rent frequencies for every singleloop detector and turn off gate

TERMINAL INPUT CONNECTIONS

SAFETY LOOP SYSTEMCENTER LOOP SYSTEMCaution:Suggested for vehicles 14 feet long or longer. If a vehicle is shorter,a center loop system is recommended

ACCESS DOOREXIT LOOP SYSTEM30'22'4'15'4'11⁄2"1⁄4"4'4'4'4'The reason for an exit loop is so the

EMERGENCY RELEASEPlace the handle and cover in originalpositions. Once the power is on, thegate will readjust itself automatically.OPTIONAL SAFETY BOL

AUDIO ALARMHOW TO REPLACE THE CONTROL BOARD2. The gate hits the driveway, curb or other,and gets stuck in an awkward position.3. Gate hinges are too t

OPTIONAL DC-1000U BACK UPSTOP BUTTON ALARM SHUT- O F FThis is an importantcommand re q u i re dto stop the audioalarm in case it hasbeen triggered. Ot

U PH IL L D R IV E WAY IN S TA L L AT I O NS E C O N D A R Y E N T RA P M E N T W I R I N GElite Part # Q103IMPOSSIBLEPOSSIBLEGate can not fi

S E C O N D A R Y E N T R AP M E N T M O U NT I NG

TROUBLESHOOTING LED INFORMAT I O NEXAMPLE:The radio receiver LED is on and thegate remains open. The radio receiverhas malfunctioned in the "ON

UL LISTINGS AND INSTRUCTIONSH) For a gate operator utilizing a non-contact sensor such as a photo beam:1) See instructions on the placement of non-con

TROUBLESHOOTING TA B L EOVERLOAD LED ONAndPOWER LED OFF1.Short circuit at terminals 8 and 102.Short circuit at any of the loop detectors in the board

C S W-200 PA RT S

C S W-200 PA RTS LISTM A I N T E N A N C E1.THE GATE AREA SHOULD BE KEPT CLEAN TO INSURE PROPER OPERATION.2. MAKE SURE HINGES ARE WORKING SMOOTHLY A

AVAILABLE PRODUCTS

UL LISTINGS AND INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONSWARNING - To reduce the risk of injury or death:1. READ AND FOLLOW ALL INSTRUCTIONS.2. Never

UL LISTINGS AND INSTRUCTIONSGate – A moving barrier such as a swinging, sliding, raising lowering, rolling, or like, barrier, that is a stand-alone pa

CONCRETE PAD AND GATE AT TA C H M E N T1/2" x 3 1/2"RED HEAD BOLTCONCRETE PADBELL BOX3⁄4" PVC24"28"28"24"6"

C O M PA CT I N STA L L AT I O N33"9"GATECOMPACT INSTALLATION ONLY:DO NOT USE THESE MEASUREMENTS FOR A STANDARD INSTALLATION. T H I S I S

Distances (A) thru (E) are from the center of one pivot point to the center of another pivotpoint.SUGGESTION: If the gate is longer than 18 feet, foll

G ATE AR M I NS TA L L AT I O NOnce the gate arm measurements are calculated, weld the bracket on the gate. Weld the longerarm first, then weld the